Loading
Your freshly painted walls may look perfect at first. However, over time, cracks, peeling, or uneven patches start to show. The culprit? Skipping wall putty. It is a compound that is applied to walls before painting. Putty creates a smooth and uniform surface by filling in imperfections like small cracks and undulations.
Whether you are renovating an old home or finishing a new one, putty for wall is the silent hero that makes your walls look smooth, strong, and paint ready. Without it, even the best paint cannot last long. Moreover, among the many options available, Birla Wall Putty is trusted across India for its quality, durability, and finish. Let’s understand how wall putty really works.
To get a perfect finish, using the right tools is essential. Here are the basic tools needed for applying wall putty:
| Tool | Purpose |
| Sandpaper | Removes old flakes, dust, and loose particles |
| Putty Blade / Scraper | Used to apply putty evenly and remove excess material |
| Wire Brush | Cleans rough surfaces or old plaster |
| Sponge | Smoothens the surface between coats |
| Mechanical Mixer (optional) | Ensures consistent, lump-free mixing |
| Clean Water | Essential for mixing and wetting the surface |
Birla Wall Putty stands out as India’s Asli Aur Sabse Safed Putty. It is a water-resistant, white cement-based putty enriched with Extra HP Polymers that:
Strengthen surface bonding
Provide a super smooth finish
Resist moisture and flaking
Enhance paint brightness with a superior refractive index
Extend the life of your paint
Besides these amazing benefits, WallCare Putty is also a zero VOC, green certified product with anti-carbonation and anti-fungal properties. This makes it perfect for both interior and exterior walls.
Applying putty correctly is crucial for its effectiveness. Here's a step-by-step guide to show you how to apply wall putty on wall using Birla Wall Putty:
Step 1: Surface Preparation
Remove all loose material, dust, and dirt from the wall using sandpaper or a wire brush. Ensure the walls are clean, dry, and free from oil or grease.
Step 2: Mixing the Putty
Add Birla White WallCare Putty to 36-38% clean water slowly and mix it well for 10-15 minutes until you get a smooth paste.
Tip: Mix only the amount you can use within 3-3.5 hours
Step 3: Pre-Wet the Wall
Before applying putty, dampen the surface with clean water. This ensures better bonding and spreads smoothly.
Step 4: First Coat Application
Apply the first coat of putty using a putty blade in an upward direction for better control and less wastage. Let it dry for at least 3 hours.
Step 5: Sanding
Check if the first coat is dry. Then, smooth the surface gently with a wet sponge or putty blade to remove any loose particles.
Step 6: Second Coat Application
Apply a second coat if necessary. Let the surface dry completely. You must preferably leave it to dry overnight.
Step 7: Final Finish
If needed, gently sand the wall with waterproof emery paper to achieve a glossy white finish before painting.
To ensure a lasting finish, follow these simple do’s and don’ts to achieve the best results:
| ✅Do’s | ❌Don’ts |
| Clean the surface thoroughly before applying putty | Don’t apply putty on dusty or oily surfaces |
| Use clean, fresh water for mixing | Don’t add water to the mix after it is prepared |
| Maintain the recommended mix ratio | Don’t use hard tools for sanding the final coat |
| Apply putty in thin and even coats | Don’t apply a thick single coat, it will crack |
| Let each coat dry before applying the next | Don’t skip drying time between coats |
| Use a mechanical mixer for better consistency | Don’t over-mix or use old, dried-out putty |
Always mix small batches that can be used within a few hours
Keep the wall surface moist during application
Avoid direct sunlight and strong wind during drying
Store putty in a cool, dry place to maintain its quality
Always follow up with a primer before painting
Wall putty may not be visible after you paint your walls but its effects are long-lasting. This helps to make your home look fresh and bright. With its superior formulation and reliable performance, Birla White WallCare Putty is the perfect foundation for any wall. So, the next time you are preparing to paint, don’t skip the base. Let Birla Wall Putty do the groundwork for the walls and make sure they stay strong for years to come.
For more information, visit www.birlawhite.com.
